 |
 |
The High Mounting Eagle Motion Detector (PN: 10EAGLE1HM) nd technology combined with digital processing to assure a
sharp, stable activation pattern with outstanding adjustability.
|
|
| |
|
 |
 |
|
The Falcon’s state-of-the-art microprocessor and flat
antenna provide the ability to disregard pedestrians
and only allow large masses (such as trucks and forklifts)
to be detected-even at lower mounting heights. |
|
| |
|
 |
 |
The FlexIR is a light beam
flexible mounting bracket
that prevents BEA's Microcell system
from damage when installed away
from the door Jamb surface. |
|
| |
|
 |
 |
|
With more standard features
than any other loop detector
on the market, the Matrix2-S
has the flexibility, compatibility
and performance to maximize
productivity and safety
on your site. |
|
| |
|
 |
 |
| The
MT22 mounts directly to doors
with accepting double L-angle
bottom bars. No mounting
channel required. |
|
| |
|
 |
 |
|
The low profile MU21 allows for minimal
over-travel. The mounting flaps wrap around the bottom
of the door for direct mounting. Try aluminum or
wood trim to give a "finished look". |
|
| |
|
 |
 |
| The Patriot Telescopic
Non-Contact SensingEdge is manufactured to work with
Rapid Roll and Sectional Doors. The system consists
of a Control Unit, Emitter Eye and a Receiver Eye which
simply mounts into a rigid steel, spring loaded retracting
arm. The arms are mounted to the bottom of the door
and extend below the leading edge of the door, thus
providing an invisible infrared beam of protection.
If the beam is blocked by an object or person below
the door, the control unit signals the door operator
to stop and/or reverse. |
|
| |
|
 |
 |
| The
Patriot Z-Flap Non-Contact
SensingEdge is manufactured
to work with Rolling Steel
and Sectional Doors. The
system consists of a Control
Unit, Emitter Eye and a Receiver
Eye which simply mounts into
a flexible molded Z-Flap
mounting bracket made of
Dupont Hytrel®. The Z-Flaps
are mounted to the bottom
of the door and extend below
the leading edge of the door,
thus providing an invisible
infrared beam of protection.
If the beam is blocked by
an object or person below
the door, the control unit
signals the door operator
to stop and/or reverse. |
|
| |
|
 |
 |
|
The Miller Edge Model
MWT02 gate and door edge transmitter is designed
to provide obstacle sensing protection for a variety
of motorized gates and doors. |
|
| |
|
 |
 |
|
The Miller Edge Model MWTA02
gate and door edge transmitter is designed to provide
obstacle sensing protection for a variety of motorized
gates and doors. The Model MWTA02 is available with
an Audible Alarm feature that activates when the
battery has only 25% of its life remaining, indicating
the battery should be replaced. |
|
| |
|
 |
 |
|
Both the Miller Edge receiver and transmitters are designed
to have several selectable options not found on other
radio controls. Simply select these options with the
convenient dip switches and wire harness. The receiver
will operate on either 12 or 24 volt AC or DC and is
capable of sending a pulse or continuous signal. |
|
| |
|
 |
 |
|
Both the Miller Edge receiver and
transmitters are designed
to have several selectable
options not found on
other radio controls.
Simply select these
options with the convenient
dip switches and wire
harness. The 3-channel
receiver will operate
on either 12 or 24 volt
AC or DC and is capable
of sending a pulse or
continuous signal. |
|
| |
|
 |
 |
|
The Miller Edge Model MWCK02 gate
and door edge transmitter and receiver kit is designed
to provide a fully reliable, self-checking communication
between the 4-wire SensingEdge and the door or
gate motor operator. When the SensingEdge detects
an obstruction, a fault condition is communicated
to the transmitter and the receiver. The signal
is then passed on to the motor operator to control
the motion of the door or gate. |
|
| |
|
|
