 |
 |
The High Mounting Eagle Motion Detector (PN: 10EAGLE1HM) nd technology combined with digital processing to assure a
sharp, stable activation pattern with outstanding adjustability.
|
|
| |
|
 |
 |
|
The Falcon’s state-of-the-art microprocessor and flat
antenna provide the ability to disregard pedestrians
and only allow large masses (such as trucks and forklifts)
to be detected-even at lower mounting heights. |
|
| |
|
 |
 |
The FlexIR is a light beam
flexible mounting bracket
that prevents BEA's Microcell system
from damage when installed away
from the door Jamb surface. |
|
| |
|
 |
 |
|
With more standard features
than any other loop detector
on the market, the Matrix2-S
has the flexibility, compatibility
and performance to maximize
productivity and safety
on your site. |
|
| |
|
 |
 |
| The low profile
MT21 is flame retardant and will not release harmful
gases or fumes. This edge mounts directly to doors
with accepting double L-angle bottom bars. |
|
| |
|
 |
 |
|
The MT22 mounts directly to doors with accepting double L-angle
bottom bars. No mounting channel required. |
|
| |
|
 |
 |
| Ideal for
1-3/4 to 2 inch thick doors. The flexible flaps
wrap around the bottom of the door for direct
mounting. Try aluminum or wood trim to give
a "finished look". |
|
| |
|
 |
 |
The ME120
is designed for use on doors and gates up to 1-1/2
inches thick. To install, simply attach the rigid
PVC or aluminum mounting channel and slide sensor
into the channel.
 |
|
| |
|
 |
 |
The ME123
is designed for use on 1-1/2 to 2 inch thick doors
and gates. To install, simply attach the rigid
PVC mounting channel and slide sensor into the
channel.
|
|
| |
|
 |
 |
| The
Patriot Telescopic
Non-Contact SensingEdge
is manufactured to
work with Rapid Roll
and Sectional Doors.
The system consists
of a Control Unit,
Emitter Eye and a Receiver
Eye which simply mounts
into a rigid steel,
spring loaded retracting
arm. The arms are mounted
to the bottom of the
door and extend below
the leading edge of
the door, thus providing
an invisible infrared
beam of protection.
If the beam is blocked
by an object or person
below the door, the
control unit signals
the door operator to
stop and/or reverse. |
|
| |
|
 |
 |
| The
Patriot Z-Flap Non-Contact
SensingEdge is manufactured
to work with Rolling
Steel and Sectional
Doors. The system consists
of a Control Unit,
Emitter Eye and a Receiver
Eye which simply mounts
into a flexible molded
Z-Flap mounting bracket
made of Dupont Hytrel®.
The Z-Flaps are mounted
to the bottom of the
door and extend below
the leading edge of
the door, thus providing
an invisible infrared
beam of protection.
If the beam is blocked
by an object or person
below the door, the
control unit signals
the door operator to
stop and/or reverse. |
|
| |
|
 |
 |
| The
Miller Edge Model
MWCK02 gate and door
edge transmitter and
receiver kit, is designed
to provide a fully
reliable, self checking
communication between
the 4-wire SensingEdge and the door or
gate motor operator.
When the SensingEdge
detects an obstruction,
a fault condition
is communicated to
the transmitter and
the receiver. The signal
is then passed on
to the motor operator
to control the motion
of the door or gate. |
|
| |
|
 |
 |
|
The Miller Edge Model MWT02 gate
and door edge transmitter is designed to provide
obstacle sensing protection for a variety of motorized
gates and doors. |
|
| |
|
 |
 |
|
The Miller Edge Model MWTA02 gate
and door edge transmitter is designed to provide
obstacle sensing protection for a variety of motorized
gates and doors. The Model MWTA02 is available with
an Audible Alarm feature that activates when the
battery has only 25% of its life remaining, indicating
the battery should be replaced. |
|
| |
|
 |
 |
|
Both the Miller Edge receiver and
transmitters are designed to have several selectable
options not found on other radio controls. Simply
select these options with the convenient dip switches
and wire harness. The receiver will operate on either
12 or 24 volt AC or DC and is capable of sending
a pulse or continuous signal. |
|
| |
|
 |
 |
|
Both the Miller Edge receiver and
transmitters are designed
to have several selectable
options not found on
other radio controls.
Simply select these
options with the convenient
dip switches and wire
harness. The 3-channel
receiver will operate
on either 12 or 24 volt
AC or DC and is capable
of sending a pulse or
continuous signal. |
|
| |
|
