| MEL-K20
|
MEL-K20 MEL (Monitored Edge Link) Transmitter and Receiver
MEL provides a wireless transmission from a
Sensing Edge to operator controls
eliminating the need for hard wired coil
cords or retractable reels.
The MEL system includes a transmitting unit
that wires to a monitored edge sensor and a
receiving unit. MEL has a built-in feature
to detect the presence and function of a
monitored entrapment protection device. If
the device detects a fault in the system,
MEL features LED indicators to simplify diagnostics. |
|
Specs
Installation
FAQ
Warranty
 |
| |
MEL-RX20
|
MEL-RX20 MEL (Monitored Edge Link) Receiver
MEL-RX20 receives a monitored Sensing Edge signal from the MEL-TX20 transmitter eliminating the need for hard wired coil cords or retractable reels. Operates on 12-24vAC/DC.MEL-RX20 features LED indicators for simplified diagnostics.
|
Specs
Installation
FAQ
Warranty
|
| |
MEL-TX20
|
MEL-TX20 MEL (Monitored Edge Link) Transmitter
MEL-TX20 transmits a monitored Sensing Edge signal to the MEL-RX20 receiver eliminating the need for hard wired coil cords or retractable reels. Operates on two (2) "AA" lithium batteries and is housed in a NEMA4 enclosure. |
Specs
Installation
FAQ
Warranty
|
| |
MWRT02
|
MWRT02 Receiver and Transmitter
Includes single channel receiver (MWR02A) and transmitter (MWT02). The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.
|
Specs
Installation
Warranty
|
| |
MWRTA02
|
MWRTA02 Receiver and Transmitter with Audible Low Battery Alarm
Includes single channel receiver (MWR02A) and transmitter (MWTA02) with audible low battery alarm. This feature that activates when the battery has only 25% of its life remaining, indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals.
The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.
|
Specs
Installation
Warranty
|
| |
MWR02A
|
MWR02A Single Channel Receiver
The receiver will operate on either 12 or 24 volt AC or DC and provides N.O. or N.C. output.
For use with MWT02 or MWTA02 transmitter. |
Specs
Installation
Warranty |
| |
MWT02
|
MWT02 Sensing Edge Transmitter
Wirelessly transmits signal to compatible receiver (MWR02A)
|
Specs
Installation
Warranty
|
| |
MWTA02
|
MWTA02 Sensing Edge Transmitter with Audible Low Battery Alarm
Includes a built in Audible Alarm feature that activates when the battery has only 25% of its life remaining, indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals. For use with MWR02 or MWR03 receiver. |
Specs
Installation
Warranty |
| |
MWR03
|
Works with most gate and commercial door operators. The one receiver is capable of receiving signals from up to 3 different input devices.
|
Specs Installation
Warranty
|
| |
MWHT01
|
MWHT01: Hand Held Transmitter
One button single channel remote control transmitter with visor clip.
9 switch control for easy code setting
|
Specs
|
| |
MWKT01
|
Mini Keyfob Transmitter
Single button remote control with visor clip.
|
Specs
|
| |
ANT-R
|
ANT-R: Rigid Antenna, Insulated
Use to increase signal reception when needed.
|
|
| |
ANT-K
|
ANT-K: Antenna Cable
COAX Cable and connector block.
Use to increase range when needed.
|
|
| |
TB-01
|
TB-01 Transmitter Mounting Bracket
Aluminum mounting bracket with pre-drilled holes and slots for easy
mounting to 2” round posts.
|
|
| |
MWCK04
|
MWCK04: Communicator Kit
Includes MWCKT04 edge transmitter and MWCKR04 receiver.
This kit is designed to provide a fully reliable, self checking communication
between the 4-wire Sensing Edge and the door or gate motor operator.
|
Specs
Installation
Warranty |
| |
MWCT04
|
MWCT04: Communicator Transmitter
For use with MWCKR04 receiver.
|
Specs
Installation
Warranty |
| |
MWCR04
|
MWCR04: Communicator Receiver
For use with MWCKT04 transmitter.
|
Specs
Installation
Warranty |
